10 Minute BidsPlumbing takeoffs from plans
in Pierce County.
Upload the plan set for a house in Tacoma, Puyallup, Bonney Lake and Gig Harbor. We build it in 3D and measure the plumbing off the model, with Pierce County's design numbers in view. You spend about 10 minutes checking it against your plans, and it's ready to price and send.
Priced per plan setPlumbing bid, 3D model included
Launch offer: the first 100 sign-ups get their first trade bid for $10.
Read the video transcript
Plumbing bid, straight from the plans. Upload the plans. Within minutes we've found every fixture and you see your price. The whole system in 3D: 21 fixtures on two floors. Drain, waste and vent through 6 stacks: 309 ft of drain. Every vent stack to its pipe boot: 4 boots, marked for the roofer.
Supply color-coded hot and cold: 419 ft of cold water line. Tubs, showers, laundry and hose bibs counted; open items flagged. Pipe and fittings by size and fixture sets, in a draft bid you can price and send. Plus a supplier order sheet: save it as a PDF and email it. Every pipe and fitting.
Upload your plans at 10minutebids.com
Example house · address hidden
The local numbers behind a plumbing bid.
What Pierce County builds to, and what it means for the takeoff.
| Where | Frost depth | Winter design temp. | Energy code climate zone |
|---|---|---|---|
| Tacoma | 12 in | 29 °F | 4C |
- Frost depth: 12 in (Tacoma). The water service and any outdoor lines run below it.
- Winter design temperature: 29 °F (Tacoma). Frost-free hose bibbs, and protection for any pipe in an outside wall or a crawl space.
- Washington plumbing follows the 2021 Uniform Plumbing Code, not the International Plumbing Code.
Sources: Tacoma: City of Tacoma Ordinance No. 28957. Read 2026-09-28. Climate zones: Washington State Energy Code, Table R301.1. Every number is as the jurisdiction publishes it (its design criteria for houses, IRC Table R301.2(1)); a dash means it isn't published. Your lot can differ with elevation and exposure, so confirm it with the building department before you order.
Every fixture and every run.
The takeoff is built from the model, run by run. Here's what it covers, with the numbers from our example house.
- Every fixture, read off the plans
- Drain, waste and vent runs
- PEX hot and cold runs to each fixture
- Water service and building sewer
- A supplier order sheet to save as a PDF and email to your supplier. See a sample
Every trade in Pierce County.
Add another trade to the same order: each one after the first in the same order is half price. All of Pierce County · Every area
Plumbing takeoffs in Pierce County
Do you do plumbing takeoffs for houses in Tacoma?
Yes. Upload the plan set for a house anywhere in Pierce County (Tacoma, Puyallup, Bonney Lake, Gig Harbor, Lakewood and University Place), or anywhere else. Nothing has to be built yet: we measure the house on the plans.
What design numbers apply in Tacoma?
Tacoma publishes frost depth: 12 in; winter design temp.: 29 °F; energy code climate zone: 4C. The design on your plans should match them, and the takeoff follows your plans. Elevation and exposure can change them for your lot, so confirm with the building department.
Does a takeoff cost more in Pierce County?
No. The price is the same everywhere, and you see it before you pay. The 3D model is included, and each trade after the first in the same order is half price.
Is this an exact price?
No. It's an estimate built from your plans. Plans don't show code or inspector changes, the existing water and sewer service, or fixtures moved during construction. Anything built differently from the drawings won't be in the bid. We recommend a site visit to confirm measurements and conditions before you sign a contract or order materials.
Have a plan set?
Send it in.
Any house in Pierce County. The 3D model and the takeoff come off your own plans.