10 Minute BidsFraming takeoffs from plans
in south King County.
Upload the plan set for a house in Renton, Kent, Auburn and Federal Way. We build it in 3D and measure the framing off the model, with South King County's design numbers in view. You spend about 10 minutes checking it against your plans, and it's ready to price and send.
Priced per plan setFraming bid, 3D model included
Launch offer: the first 100 sign-ups get their first trade bid for $10.
Read the video transcript
Framing takeoff from a plan set, without the highlighters. Upload the plans. Within minutes we've read every sheet and you see your price. We trace the walls off the floor plans and frame the house in 3D, stick by stick. 705 ft of exterior wall, every stud, plate and header, 90 trusses.
The garage is slab on grade: no floor framing, treated plates on the concrete. 1,785 pieces of lumber to buy, by size and length. Every piece on a cut list. Tap a line and the model shows where it goes. Sheathing, hardware, nails and crew days go into a draft bid you can price and send.
Plus a supplier order sheet: save it as a PDF and email it. Every stick, every box of nails. Upload your plans at 10minutebids.com
Example house · address hidden
The local numbers behind a framing bid.
What south King County builds to, and what it means for the takeoff.
| Where | Snow load | Design wind speed | Seismic design category | Frost depth |
|---|---|---|---|---|
| Auburn | 25 psf (ground) | 110 mph | D2 | 12 in |
| Federal Way | 25 psf (ground) | 95 mph | D2 | 12 in |
- Snow load: 25 psf (ground) (Auburn). The trusses, rafters and roof sheathing on your plans are designed for the snow load; if the truss notes show a different number, ask before you bid.
- Design wind speed: 110 mph (Auburn). Straps, hold-downs and wall bracing on the plans follow it.
- Seismic design category: D2 (Auburn). Braced wall panels, hold-downs and anchor bolts follow the seismic rules; they are on the plans' shear wall sheet, and in the hardware list.
- Frost depth: 12 in (Auburn). The footings go below it (foundation work, shown for reference).
- Houses in Washington are built to the 2021 International Residential Code, with state amendments.
Sources: Auburn: City of Auburn · Federal Way: City of Federal Way Community Development, Building Division. Read 2026-09-28. Every number is as the jurisdiction publishes it (its design criteria for houses, IRC Table R301.2(1)); a dash means it isn't published. Your lot can differ with elevation and exposure, so confirm it with the building department before you order.
Every stick on a cut list.
Your takeoff is built from the model, not highlighters on a plan. Here's what it covers, with the numbers from our example house.
- A cut list: studs, plates, headers, joists, rafters and trusses
- Lumber by size and stock length, with waste
- Trusses by span and pitch
- Wall sheathing, hardware and nails
- A supplier order sheet to save as a PDF and email to your supplier. See a sample
Every trade in south King County.
Add another trade to the same order: each one after the first in the same order is half price. All of South King County · Every area
Other trades
Framing takeoffs in South King County
Do you do framing takeoffs for houses in Renton?
Yes. Upload the plan set for a house anywhere in south King County (Renton, Kent, Auburn, Federal Way, Burien and Tukwila), or anywhere else. Nothing has to be built yet: we measure the house on the plans.
What design numbers apply in Auburn?
Auburn publishes snow load: 25 psf (ground); design wind speed: 110 mph; seismic design category: D2; frost depth: 12 in. The design on your plans should match them, and the takeoff follows your plans. Elevation and exposure can change them for your lot, so confirm with the building department.
Does a takeoff cost more in South King County?
No. The price is the same everywhere, and you see it before you pay. The 3D model is included, and each trade after the first in the same order is half price.
Is this an exact price?
No. It's an estimate built from your plans. Plans don't show field changes: walls moved on site, extra blocking, or framing an engineer or inspector asks for. Anything built differently from the drawings won't be in the bid. We recommend a site visit to confirm measurements and conditions before you sign a contract or order materials.
Have a plan set?
Send it in.
Any house in south King County. The 3D model and the takeoff come off your own plans.